The whole electrical circuit is disconnected. When the pointer be started. Rotate it clockwise to full stop for locking neutral mode. In this position, the key can be removed and the position, the engine will start only after the circuit closes up.
ON for parking on roadside at night. To press this button can turn on the starting motor circuit. When the ignition switch is ON, the gear shifter must The front brake means that the brake lever of the left be set to NEUTRAL position so as to cut off driving for handlebar is gripped slowly towards the control handle of the safety.
The starting button should not be held for more than five seconds each time. Otherwise the excessive discharge The grip is used to control the speed of the engine. Turn will cause the wiring and starting motor to be hot abnormally.
After turning, move the switch to middle position; the turning lamp will be turned off. After the turning has been finished, switch off the turning lamp in time. Press this button to make the horn sound. Grip this lever to disengage the driving system at the This motorcycle is equipped with the choke system, time of starting the engine or shifting the gear. Disengage the which makes the starting easier. Push down the choke lever to clutch by grasping the lever.
When the engine acquires headlamp will be switched to high beam mode; the high beam the normal working temperature, reset the choke lever to indicator in the instrument panel will be lit simultaneously. When the engine is in the state of high temperature, there is no need to use the choke system for starting. Never spill gasoline on hot engine. Never add the fuel from above tank inlet as shown in the Fig. Otherwise To open the cap, insert the ignition key and turn it expansion of the gasoline owing to higher temperature clockwise.
Then the cap can be removed together with the will cause overflow. To close the cap, align with the arrow and push down the The engine should be stopped during the refilling, cap and the key on the hole of the tank cap till the locking and the ignition switch should be turned to OFF.
No sound is heard. Finally pull out the key. This model of motorcycle is equipped with a five-shift gear-in transmission system. When stepping on this pedal, the rear brake functions CAUTION and the brake indicator on the instrument panel will be lit In the neutral gear, the green indicator on the simultaneously.
Although the indicator is lit, it is still advised to release the clutch lever slowly, and confirm the transmission system is really in neutral mode. Before you shift to lower gear, you need to slow down the motorcycle. Before the clutch is engaged, the engine speed should be raised at the time of shifting to lower gear. This can.
To place the cycle on the center stand, step your foot on the lever of the center stand, holding the rear clothes-rack with right hand, gripping the handlebar with your left hand and pull it upwards and backwards physically so that the motorcycle can be fixed on the stand.
To locate the motorcycle on the side stand, put your foot on the end of the stand, then step on downwards physically till the stand moves to the full stop and rest upon the stopper.
When the motorcycle stops on the slope, let its WARING front end toward the high direction of the slope to avoid When engine starts, check if the starting lever sliding from the side stand, and also engage the bottom return to its normal position. WARNING Before start, check if the side stand returns to its normal position, and whether there is any looseness or unstability on the stands. The cock is usually set to this position. The gasoline can be supplied through this cock to the carburetor, each time the handlebar of the throttle is turned.
Set the tap to OFF after the engine stopped. Park the vehicle may occur, i. This may cause serious damage to the ring to the required position. The first stage is the softest and mechanical system when the engine is started.
The springs of both sides shall be at the same Fuel Hose stage. Otherwise, it may cause an unstable steering If the fuel hose is worn out, replace it in time. If slight explosion sound comes from the engine, the possible cause is to use general fuel as a substitute, thus replace the fuel.
Note: Using leadless gasoline can prolong the lifetime of the spark plug. Use of high quality 4-stroke engine oil would extend the Cycle saddle lock lifetime of the engine. If this oil is not available, please purchase appropriate substitutes according to the data listed below.
The FOREWORD has stated that correct running-in You may engage to different gears to speed up, provided that operation is important to prolong the service life and making the above speed limits are not exceeded. However, during the the best of a new motorcycle. This chapter provides the correct first 1, km, never turn the throttle to the maximum position. After the engine has been started, no matter cold or The maximum speed limits for a new motorcycle during warm, let the engine run at idle speed for an adequate period the running-in period are shown as below.
To 1,km Less than 7, rpm The maintenance after the first 1,km of mileage is Over 1,km Less than 10, rpm of uttermost importance to your motorcycle. At the time of running-in, all the components of engine are run in, and all the The engine speed should be changed often, instead of other parts are also engaged.
Such process contributes The timely maintenance after the first 1,km will to the engagement of the components. In order to ensure a contribute to a long lifetime and good performances.
But mind that the engine must The maintenance after the first 1,km should be not be overloaded. Never underestimate the importance Check if the throttle switch is set to ON position.
Insert of these checks. If Items to Be Purposes for Check the transmission system is currently in neutral mode, the Checked neutral indicator should be lit. Steering 1. Smoothness 2. No gap or looseness When starting the engine, the gearshift should be Lighting Operate all the lamps-headlamp, tail lamp, stop lamp, illuminated panel indicator, turning signal lamp.
Brake 1. Correct clearances of rear braking pedal, front braking connection rod. No sponge-like dull braking. The ignition switch is set to ON position; Indicator lamps Indicators of neutral gear and oil level or turning signal indicator 2. Use the choke system. Throttle 1. Correct cable clearance 3. Step on the starting rod two or three times. Smooth speeding up and swift slowing down 4.
Quickly turn the ignition switch to ON. Step on the Tires 1. Calibrate air pressure. Adequate tread depth starting rod to start the engine. No fracture or cutting Press the choke lever fully down. The throttle valve is Horn Normal performance closed. Press the starter button to start the engine. As soon as Clutch 1. Calibrated clearance of cable 2. Smooth movement the engine is started, pull the lever up by half and let the Fuel Sufficient fuel for the planned mileage engine warm up sufficiently.
Then release the lever. The cooler Driving chain 1. Calibrate tightness. Proper lubrication. The ignition switch is set to ON position release the throttle and grip the clutch lever. Move the lever 2. Then twist 3. Step on the starting rod to start the engine. Repeat this procedure and you will the electric starter button down.
When stating the engine as it be able to shift to the top gear. WARNING The gearshift is capable of making the engine smooth Never start the engine in an enclosed area with running within a normal range of operation. The transmission bad ventilation conditions.
The CO in the tail gas is ratio is carefully designed to be compliance with the radically toxic. Never keep the motorcycle running a characteristic of the engine. The rider should select the most short while without monitoring. Shift to lower gears Never let the engine running for prolonged time as necessary to get the engine working at normal speed. The engine rotary speed at any gear should not exceed the red area of the tachometer.
While gripping the clutch lever and then waiting a moment, press the gear lever to engage the bottom gear. Twist When the motorcycle runs upwards on a steep slope, it the throttle grip counterclockwise and release the clutch lever will slow down and demonstrates a lack of power. Now shift slowly and gradually. When the clutch is engaged, the to a lower gear so that the engine resumes normal operation. The action of gear shifting should be performed swiftly;. Slow down your motorcycle in such When the motorcycle runs downwards along a slope, case.
Bear in mind that the speed should not be too high in downward riding. If this is the first time for you to ride this type of Apply both the front and rear brakes evenly. Observe the neutral Before you start and stop the motorcycle, set the indicator to confirm the neutral gear.
As the speed is high, the braking distance will be longer Never shift the gear at the time of turning. Correctly judge the distance from the vehicles It is extremely dangerous to ride your motorcycle ahead. The distance should be at least enough for you to with a single hand. Hold the handlebars firmly with brake the motorcycle.
Rest your feet on the footrests. Never let Less-experienced rider tends to use the rear brake only. It will speed up the wearing of the rear brake and make the Because the tire friction becomes low on wet and braking distance longer. Care should further maintenance, instructions.
The steering assembly, be taken when riding on a wet or slippery road and at a shock absorbing system and the wheel system require the curving road. In such cases, use the brakes gently. Hurried special and careful maintenance. For the sake of safety, it is advised that qualified workers If the motorcycle must be supported with the side stand shall service these components.
Return to the must be carried out as soon as the odometer reading neutral gear prior to starting the engine. Carry out the regular Remove the key from the switch. It is recommended maintenance according to the intervals based on odometer that you use genuine Qingqi brand parts or their reading or the number of months.
At the end of each interval, equivalents. The others may should be carried out. If your motorcycle has been used under be maintained by yourself under the instructions of bad conditions, for example, continuously running with large this Manual. A tool kit placed in the small bag on the left lower side of the chassis is available to your regular maintenance, which include the tools listed below. The battery fluid level is visible by removing the left chassis cover.
If the level is below the lower limit, add distilled. Tap water is absolutely prohibited for this purpose. Ensure one end of the air hose is connected closely to the battery fitting and the other end is always kept open. The air vent pipe should not be mistaken After the first 1, km or every 3, km, clear out the and the battery should be placed in the right position. Readjust the spark plug gap with a gap gauge so as to keep it between 0.
Replace the plug terminals are correctly connected. The red lead must with a new one after every 6, km. Any mistake in wiring the porcelain tip. The color can tell you if the standard spark may cause damage to the charging system and the plug apply to your motorcycle. In case of being wet or black battery itself. The normally worked spark plug usually is light the authorized dealers to check the electrolyte gravity of the gray or light brown.
If the spark plug is white or seem flashing, battery with a gravity gauge. The battery operating condition it shows that the spark plug works under the overheat condition. In such case, renew the spark plug with a cold type can be judged according to the gravity. The two most important maintenance tasks In case of being 2C6 D7EA X22ES wet, use this kind are the daily oil level checking and the regular oil change.
Use U this plug instead. Never start the scope. If the color of spark plug is different from the standard engine with a low oil level. Never refill oil over the one, consult with dealers before changing other types of upper limit of the view glass.
Selection of improper spark plug will lead to serious damage to the engine. Change transmission oil after the first km and Choosing improper spark plugs can make operation very every km thereafter. Carry out oil change with a warm difficult. So contact with your dealer before using other engine, so as to empty the old oil thoroughly, as follows: brands of spark plugs. Park the vehicle on its central stand. Remove refilling cap. Remove three screws on oil filter cover.
Take off the cover, pull out the element and replace with a new one. Precaution: Insert the open part of filter element into the engine. Make sure all parts are firmly installed.
Before replacing the cover, make sure all springs and gaskets of the filter are correctly installed. Precaution: I drain plug Gaskets must be replaced with new ones. Remove drain plug on engine bottom and empty the 7. Install the cover and tighten the screws with moderate oil. Replace drain plug. Fill about ml of fresh engine oil into the refilling port under filter cap.
Replace the cap. Note: In case of changing oil without replacing element, it needs ml of fresh engine oil. Start engine and run it at idle speed for a few seconds. Precaution: Make sure there is no leakage around the filter cap. Check oil 2 screws 3 filter cover level at the view glass. Precaution: Precaution: The vehicle uses ethanol hydraulic fluid for brakes. Please always use the engine oil recommended No silicate or petrol products shall be mixed with it.
Otherwise, the braking system may be damaged. Never use any fluid left in the last maintenance, because it Check brakes after the first km and every km may absorb moisture in the air. Always use SAE J thereafter. Never splash brake fluid onto painted or The vehicle uses disc bake in front wheel and drum plastic surfaces, or corrosion may occur. Correct brake operation is critical to safe Check frequently the level of brake fluid tank, Replenish driving. Always have the regular brake check executed by with recommended fluid.
The level may get lower along with qualified distributors. Brakes are the parts related to personal safety. Always keep it in good adjustment. In case of drinking by mistake, vomit it out by force.
In case of contacting eyes and skin, wash with plenty of clean water before moving to hospital. Check for any leakage in front braking system. Check for any leakage or crack in hydraulic pipes. Check brake grip and brake pedal and keep them with proper spring-up force. Check the wearing conditions of front brake. Apply brake for several times to make the brake lining extended, restore the spring Check the front brake lining to see if it is worn to the force and bring the brake fluid into circulation.
If it reaches the mark, replace brake lining. He has the right tools and skills to fulfill it in the safest and most economical manner.
Precaution: Disc braking system involves high pressure. For the sake of safety, replace the hydraulic pipes and fluid at the interval stipulated in the maintenance schedule. Front brake lamp switch is under the brake grip. Loosen Items for daily check of braking system: the screw and move the switch unil the lamp can be lit just. The wearing limit marks are impressed on both front and rear brakes. Check if the braking system is properly adjusted. Check if the mark extension line is within the allowed limit.
If the extension line exceeds the limit, entrust the dealer to have the brake assembly replaced for the safe purpose. This switch is mounted at the right chassis. To adjust it up and down can make the brake lamp being lit on treading on The clearance can be adjusted to mm by screwing pedal with a little force.
The muffler pipe of the motorcycle ridden for a long. When changing the failed bulb, the one with the same rated value must be used. Otherwise it may cause overload of the electric circuit system and early damage to the bulbs. The fuse box is installed in the cover of left chassis. If some troubles occur in an electric system, the fuse must be checked.
If the fuse is burned out, the standby one 15 A in the fuse box will be replaced. Never substitute for the burned fuse with aluminum foil, copper wire, etc.
If the new fuses are burned out in a short time frequently, this shows there is the possibility of 1. Loosen three screws and take off the small lamp more serious electrical trouble. Contact the dealer screen. Remove tow screws outside the headlamp and pull. Pull off the bulb holder by rotating it counterclockwise. Pull off the bulb by rotating it counterclockwise. Install a new bulb and replace the assembly. Precaution: The lamp assembly is of reflection type. Do not touch the reflection mirror in bulb repiacement to avoid reducing its service life.
Remove the lamp cover by loosing the two screws. Take off the bulb by pressing the bulb and turning to the left. Replace a new bulb with reverse order of removing. Withdraw the bright plastic flake and outer frame. Screw out the bulb by pressing and turning it to the 4. Separate the foam plastic from the outer frame. Renew a bulb. The stability of carburetor contributes to the performance of the engine. The carburetor has been adjusted If dust clogs the air filter element, intake resistance to the best state before leaving the factory.
Please do not increases as the output power decreases. The increase of attempt to make unnecessary adjustment. Note that the gasoline content in the mixing gas leads to the increasing of carburetor has two adjustment items Which are: throttle cable fuel consumption. To avoid this, check and clean the air filter clearance and idle speed.
The new motorcycle should be element as the following steps after riding for every 3, adjusted according to the following method after running for km. Remove the right chassis cover with the key. Loose the fixing screws and remove the air filter cover. Start the engine and warm it up. After warming the engine up, screw in and out the After the adjustment of cable, check the grip to adjusting screws for idle speed and let the engine run at see if it can be turned normally.
The idle speed should rpm. The idle speed should be adjusted with the engine fully warming up. Loose the locking nut. Turn the adjuster so that the cable clearance is kept within a range of 0. Tighten the locking nut after adjusting of the clearance.
If the clearance fails to meet this requirement, make an adjustment as the following method. Turn the adjuster and allow it to the required clearance 4 mm. Tighten the locking nut. After running for every 1, km, adjust the tightness During this time, lubricate the cable with machine oil. Support the motorcycle with the center stand. Remove the cotter pin and loose the nut of rear wheel shaft. Screw out the locking nut. The chain can be adjusted by turning the adjusting bolt clockwise and counterclockwise.
Note:When a new chain is replaced, the two chain wheels must be checked. If necessary. But excessive air pressure may decrease the contact area between the tire and ground, lead to the slipping of motorcycle and even losting of control.
The air pressure should be always kept within the specified limit. Adjust the air pressure when the tire is cold. Air pressure of tires: Front tire: kpa Rear tirekpa 1 Joint clip 2 Rotating direction The dust and dirt on the driving chain will increase the wearing of the chain itself and chain wheels.
Therefore, clean the driving chain with cleaning agent and then lubricate it using special lubricant or motor oil after riding for every 1, km. After the first 1, km and every 3, km, check the air pressure and tire tread. For the sake of safety and longer Riding on the motorcycle with its tire excessively worn service time, the air pressure of tire should be often checked. When the depth of outer tire tread is If the air pressure of tires is not sufficient, it will not reduced to 1.
Insufficient air pressure makes. Do not The air pressure of tires is very important for twist the filter element to avoid cracking. Soak the filter element into the pool of motor oil and There fore, often check the wearing state and air squeeze the oil out of the element and let it slightly wet. If any crack is found, renew the In order to reduce the pollution caused by exhausting of filter element. Reassemble the cleaned filter in the reverse order of removal. Make sure that the filter element is firmly installed Clean according to the following steps.
Observe the abnormal sound of the engine. We stock a full range of extras. Air Filters. We supply all documents required for 1st Registration in UK. Certificate of Newness V The Registration fees are currently? Tax Disc Holder and 12 Months Tax - all for only? Delivery is scheduled for 1 - 3 working days after purchase or we can arrange a convenient appointment for you to collect from our warehouse in Durham.
Phone for more information on Nationwide delivery available from? Returns accepted within 7 days at expense of purchaser.
0コメント